Click to enlarge Image is similar

• Protocol: DCC
• Output current: ~1 A
• Kit version: 1.5
• Firmware version: 0.24.00

This kit contains SMD components. However, soldering SMD components is much easier than expected ( 'Der richtige Umgang mit SMD' (Source: ELVjournal, German language)). You can also purchase this kit with partially preinstalled SMD components (see 'Available Options' below).

Construction manual, schematics and PCB layouts are delivered on a CD-ROM, including firmware (if applicable) and a great deal of additional information.

This kit comes with a pre-programmed processor.

For more information, please visit  the product pages on the internet.

Difficulty level:

Click the clipboard icon to check the recommended tools for this kit.

The standard version of this kit consists of these components:   » 1 x PCB Set "Central Station Z1"         » 1 x ATmega644PA-PU         » 1 x 74AC244N         » 1 x AMSR-7805-NZ         » 1 x FT232RL         » 1 x L6206N         » 1 x LM393P         » 1 x MAX232         » 1 x 1N4004         » 4 x 1N4148         » 1 x LED, red, low current (3 mm)         » 1 x LED, yellow, low current (3 mm)         » 2 x LED, green, low current (3 mm)         » 2 x SFH628A-4         » 1 x Cooling and stiffening plates for OpenDCC Z1         » 2 x Wire wound resistor, 0.15 Ω, 1 W         » 2 x Metal film resistor, 1 Ω, 2W         » 8 x Carbon resistor, 47 Ω, 1/4 W         » 1 x Carbon resistor, 100 Ω, 1/4 W         » 1 x Carbon resistor, 220 Ω, 1/4 W         » 6 x Carbon resistor, 1.5 kΩ, 1/4 W         » 2 x Carbon resistor, 2.2 kΩ, 1/4 W         » 1 x SMD resistor, 4.7 kΩ (1206)         » 4 x Carbon resistor, 10 kΩ, 1/4 W         » 1 x SMD resistor, 10 kΩ (1206)         » 1 x Carbon resistor, 13 kΩ, 1/4 W         » 1 x Carbon resistor, 15 kΩ, 1/4 W         » 1 x Carbon resistor, 39 kΩ, 1/4 W         » 2 x Carbon resistor, 220 kΩ, 1/4 W         » 2 x Carbon resistor, 1 MΩ, 1/4 W         » 2 x Ceramic capacitor 18 pF         » 3 x Ceramic capacitor 1 nF         » 2 x Ceramic capacitor 4.7 nF         » 5 x Ceramic capacitor 10 nF         » 1 x Film capacitor 10 nF MKT         » 13 x Ceramic capacitor 100 nF RM5         » 4 x SMD multilayer capacitor 100nF (1206)         » 1 x Ceramic capacitor 220 nF         » 1 x Film capacitor 1 µF MKS2         » 5 x Electrolytic capacitor, 1 µF / 50 V         » 2 x Electrolytic capacitor, 10 µF / 50 V         » 1 x Electrolytic capacitor, 100 µF / 16 Volt         » 1 x Electrolytic capacitor, 220 µF / 35 Volt         » 1 x Electrolytic capacitor, 470 µF / 35 Volt         » 1 x Standard Crystal, 16 MHz         » 1 x PTC Resettable Fuse 1.8 A         » 1 x PCB push button red         » 1 x PCB push button green         » 2 x Header 1x5 pin, angled, RM 2.54         » 1 x Header 1x2 pin, straight, RM 2.54         » 2 x Header 1x3 pin, straight, RM 2.54         » 1 x Header 1x4 pin, straight, RM 2.54, Wire Wrap         » 2 x Header 1x3 pin, straight, RM 2.54, Wire Wrap         » 2 x Jumper, open top, red         » 1 x Jumper, open top, black         » 8 x Angle Pin         » 1 x D-Sub socket, 9 pin, THT, angled         » 1 x Power supply chassis socket, 2 pole         » 3 x RJ45 Modular Jack horizontal unshielded         » 1 x USB panel socket, Series B, angled, SMD         » 1 x Power supply plug, 2 pole (f)         » 2 x Terminal block, plug-in, 4 pole, RM 3.5         » 2 x IDC transition 14 pins         » 1 x IC socket, 20 pins         » 1 x IC socket, 40 pins         » 1 x IC socket, 8 pins         » 4 x IC socket, 2 pin, single row         » 1 x IC socket, 16 pins         » 1 x Ribbon cable 14-pole, grey, 20cm         » 1 x Housing TEKO CAB 022         » 1 x Front panel for OpenDCC Z1 housing         » 1 x Back panel for Z1, w/o Xpressnet         » 1 x Mounting block         » 2 x Spacer sleeve, metal, M3x20mm         » 6 x Threaded Screw M3x6 Pan Head         » 2 x Insulating Washer M3         » 4 x Tapping Screw 2.9x6.5 Pan Head